Water Purification & Detection, Light Tables, Lab Balances & More

The digital equivalents of the Thermoelectric Cold Plates (sku: 11610 & 11609).

3" diameter top plate. Cabinet dimensions 7 1/4" x 5 1/2" x 4 3/4". Power requirements 50 watts. This unit uses the most efficient solid state thermoelectric modules yet developed. DC power is supplied to these high powered modules to control temperatures between +25^o C and -20^o C depending on the set point required. All units may use air cooling with built-in fan, or tap water cooling as the heat exchanger. Equilibrium is reached in 2-3 minutes. Lightweight, portable. Has been used successfully in recrystallizations, freezing point determinations, and temperature control for physical measurements.

Learn More

3" diameter top plate. Cabinet dimensions 7 1/4" x 5 1/2" x 4 3/4". Power requirements 50 watts. This unit uses the most efficient solid state thermoelectric modules yet developed. DC power is supplied to these high powered modules to control temperatures between +25^o C and -20^o C depending on the set point required. All units may use air cooling with built-in fan, or tap water cooling as the heat exchanger. Equilibrium is reached in 2-3 minutes. Lightweight, portable. Has been used successfully in recrystallizations, freezing point determinations, and temperature control for physical measurements.

Learn More

A general duty hot plate for use in every laboratory. Has a demand type thermostatic control which holds the temperature of the flat cast aluminum top to within +/- 5^o F. Temperature range is 200^o to 700^o F. Automatic stepless control. The sturdy SS case is attractive and easy to clean. Ample ventilation keeps controls and bench tops cool, and prolongs life of the unit. Supplied with pilot light and 6' 3" cord with three-way plug. UL and CSA approved. Operates on either 110-120 VAC or 240 VAC, 50/60 Hz. Dimensions: Top plate, 6 1/4L x 6 1/4 in.W, Overall, 7 5/8L x 65 /8W x 4 1/2 in.H.

Learn More

Separate stirring and heating switches. Stirring and heating may be used simultaneously or independently. Stirring speeds adjustable between 60-1650 rpm. Recommended for stirring squeous liquids with viscosities less than or equal to 100% glycerol. One liter flask capacity. Extended safety front separates controls from hot surfaces. Thermostat controlled temperature adjustable up to 382o C. 6" x 6" solid aluminum top plate assures fast, steady heating. Includes 1/2" and 1 1/2" stir bars. Overall dimensions: 7 1/2" deep x 6" wide x 4 3/4" high. 120 VAC, 60 Hz, 500 watts. Learn More

Same mechanical features as Standard PanaVise Head, except that stem is attached to rear of head to permit positioning work closer to the work bench. Heavy-duty steel jaws may be interchanged with optional accessory nylon jaws. By combining with optional Low-Profile Base, the work piece can be swung out and away from the work bench for clearance. Learn More

Base design allows tilting, turning and rotating of head to any position. Load control knob and split-ball features permit locking, changing position or easy head removal. Three base mounting holes allow for permanent mounting on benchtop or portability when attached to Tray Base Mount, (sku: 11494). Base diameter 5", overall height 3 13/16". Learn More

This traditional distillation unit produces from 300 - 400 ml per hour from a 1000 ml flask. This water has been shown to have a conductivity of 7 x 10^-7 Mhos, and to be essentially free from biological contamination. Hardware, heating mantle and powerstat included.

Learn More

Designed specifically for wedge polishing of TEM specimens. the mount consists of a small aluminum clamping mechanism and 5 Pyrex rods which slide into the center of the clamp and are held in place when the L-bracket is tightened. Not included with the purchase of the BiPod Polisher. Learn More

Designed for quick, easy polymerization of both plastic embedding media and plastic mounting media. Specimen tray designed to hold up to 12, 3" x 1" glass slides. Ultraviolet peak radiation is 320-360 nm, so presents minimal hazard to user. Can be operated at temperatures as low as 0o C for heat sensitive specimens. Unit is compact and lightweight with external dimensions of 5 1/4" high x 5 1/2" deep x 19" wide. Has hinged top for easy access to specimen tray. Operates on 110-120 VAC, 60 Hz at less than 1 amp. Step-down transformer available for 220-240 VAC, 50-60 Hz. Replacement lamps available . Capsule holder included. Learn More