Page 5 | Incubators, Hot & Cold Plates, Light Boxes, Ultrasonic Cleaners & More

30274 - Center It - A Tube Drilling Jig

Center It is a tool for drilling pipe and other round objects. Center It is made specifically for use in a drill press. The 7/16" groove with a 118 degree angle lets you bottom drill bit to center v-block. The 5 " long, 4" wide V-block bolts to the drill press table and enables the drilling of round pieces parallel and centered. This allows you to drill any size of pipe and wood dowels.

The grooves on the outer sides eliminate slippage while holding pipes, etc., for sawing on job sites or other applications. To use, simply place Center It on the drill press table, run the bit down (with motor off) to hold the jig centered on the bit, then bolt the jig to press table. No clamping of the tube is necessary since the angled flats of the jig hold it centered. Holes will automatically be centered on the tube with no center-punching necessary. If tubing is too large to drill in a single operation it can simply be turned over.

$42.95

30275 - Bench Top Drill Press

- 5 Speeds
- 1/3 HP, 120 VAC, 60 Hz, Single Phase
- 620, 1100, 1720, 2340 & 3100 rpm
- 1/2" Drill Chuck Capacity
- 2" Maximum Spindle Stroke
- 6 3/4" Maximum Distance from Chuck to Table
- 10" Maximum Distance from Chuck to Base
- 9 1/2" Maximum Swing
- 1.89" Column Diameter
- 6 5/16" x 6 1/2" Table Size
- 23" x 7" x 17" Overall Dimensions
- 7" x 11 1/8" Base Size

$207.95

11695 - Step-Down Transformer

This unit will permit operation of the powerstat from a 220-230 volt, 50/60 Hz source.

Call For Price

11690 - Powerstat

This unit delivers 0-132 volts (2.0 amps maximum current) from a 120 volt, 50/60 Hz single phase source. Has toggle switch, fuse, 3-wire parallel blade input cord/plug set, and receptacle housed in a steel terminal enclosure.

Call For Price

11685 - Still Support Hardware

To support still. Extra heavy stand plus clamps and ring.

Call For Price

11680 - Heating Mantle

For use with a 1000 ml flask.

Call For Price

11675 - Glass Receiving Flask

Glass Receiving Flask.

Call For Price

11670 - Glass Column Condenser

Glass Column Condenser.

Call For Price

11665 - Kjeldahl Connecting Bulb

Kjeldahl Connecting Bulb.

Call For Price

11660 - Glass Stopper

Glass Stopper.

Call For Price

11655 - Glass Boiling Flask with Side Arm

Glass flash with a side arm for boiling.

Call For Price

11285 - Double Clamp Holder

Ball joints permit positioning of specimen at desired angle. Thumb screws maintain angle. Alligator type replaceable spring clamps hold work firmly. Heavy base prevents tipping. Height to crossbar is 4".

$42.95

11490 - PanaVise Vacuum Base

Portable vacuum base easily attaches to smooth, non-porous surfaces such as Formica, porcelain or stainless steel. Mounting lever attaches and releases heavy duty suction pad - moistening the pad increases its grip. Holds all Standard PanaVise heads with same variable load control knob allowing movement as in Standard PanaVise Base (sku: 11492).

$58.95

11491 - Standard PanaVise Head

Most popular vise head due to its versatility and durable construction. Fits both standard and vacuum PanaVise bases. 2 1/2" wide nylon jaws open up to 2 1/4". Tough yet gentle jaws have satin finish for improved grip.

$56.95

L03094 - Tripod Polisher Accessory - Plain L Bracket

Designed specifically for doing the first side polishing of TEM specimens. However, the plain L bracket can be used for polishing SEM cross sections if additional mounting prior to microscope viewing is to be done.

$115.00

Tripod Polisher Accessory - Slotted L Bracket - L03090 - L03090

The most commonly used bracket. It has a slot through the front to accommodate the Pyrex inserts for wedge polishing, the SEM stub mount, as well as the L59002 Wedge Polishing Mount.

$190.00

L590TS - Tripod Polisher for TEM and SEM

Base with 3 micrometer assemblies and case.

$1,725.00

LEBSD150 Polishing & Storage Kit Includes: Pre-tilt EBSD stage, 3 height segments, 2 mounting blocks for SEM stubs, 10 SEM stubs, 2 Tripod SEM stubs, Model L150 lap fixture, SampleSaver container with two tier rack, 2 stems for holding mounting blocks in

EBSD (Electron Backscatter Diffraction) Polishing and Storage Kit

The LEBSD (Electron Backscatter Diffraction) Specimen Polishing Kit is based on the Model L150 micrometer controlled lapping fixture. Two mounting blocks are included to hold a 1/8" diameter pin SEM mount for plan view preparation of a Tripod Polisher SEM mount for XSEM preparation. The stubs are secured into the block with a set screw prior to loading into the lapping fixture. The kit includes a SampleSaver FIB storage container and two tier locking rack, and pin adapters for holding the L150 mounts. A pre-tilt EBSD specimen stage is included with three height segments. The low profile mount fits most SEM load locks and can be stored in the Sample Saver without removal from the pre-tilt holder. Special Features A relatively simple and inexpensive method for mechanically polishing and mounting EBSD specimens on an SEM stub, allowing quick transfer without dismounting a prepared sample. Pre-Tilt EBSD specimen stage keeps sample at a fixed angle of 70o or the complementary angle of 20o in the chamber. The process utilizes conventional, easily available, precision abrasives and is compatible with other sample preparation equipment and consumables. The Model L150 Lapping Fixture can be utilized for other routine parallel and angled polishing processes without modification. Up to 1.25" diameter mounting blocks are available. A low force Model L150L lapping fixture is available as an option. Complete process recipes, consumable supplies, and other accessories are available and include hand lapping tray, lapping and polishing machines, hot plate/cooling tray and sample mounting devices.

Starting at: Call For Price

Digital Stir Kool, Combination Cold Plate and Stirrer w/GLASS THERMAL PROBE 5"

This unit literally pumps thermal energy down the drain. As power is applied to the rugged thermo-electric modules, heat is transferred from the cold plate to the heat exchanger. The heat exchanger is maintained at tap water temperature by a hose connection to the 1/4 inch tubing at the rear of the instrument. A flow of one liter of tap water per minute through the heat exchanger is sufficient to carry excess heat down the drain. The unit has a low temperature limit approximately 40^oC below that of the tap water. The unit is recommended for solutions up to 200ml and uses a 3 inch diameter top plate from which heat is extracted at an initial rate of 130 BTU/hr. There is a built-in magnetic stirrer with speed control which, combined with a magnet bar in the solution, will keep your solution at equilibrium. The digital meter controller is very easy to set. Just follow the simple instructions to dial in the desired temperature for your project. The controller will maintain the set point to +/- 0.1^oC accuracy.

Accessories for the Stir Kool can be found HERE.

Starting at: $1,025.00

Stir Kool, Combination Cold Plate and Magnetic Stirrer

Rapid cooling to -20^o C. Lightweight, portable. Weighs only 8 pounds. Built-in adjustable power supply. 3" top plate allows cooling of up to 200 ml of solution. Tap water cooling is used as heat exchanger. Maximum power required is 55 watts. Temperature control from +25^o C to -20^o C. Excellent wherever rapid, efficient temperature control is needed such as tissue fixation and dehydration, recrystallization, freezing point determinations and temperature control for physical measurements. Overall dimensions: 7 1/4" x 5 1/2" x 4 3/4".

Accessories for the Stir Kool can be found HERE.

Starting at: $845.00

Digital Thermoelectric Cold Plate

The digital equivalents of the Thermoelectric Cold Plates (sku: 11610 & 11609).

3" diameter top plate. Cabinet dimensions 7 1/4" x 5 1/2" x 4 3/4". Power requirements 50 watts. This unit uses the most efficient solid state thermoelectric modules yet developed. DC power is supplied to these high powered modules to control temperatures between +25^o C and -20^o C depending on the set point required. All units may use air cooling with built-in fan, or tap water cooling as the heat exchanger. Equilibrium is reached in 2-3 minutes. Lightweight, portable. Has been used successfully in recrystallizations, freezing point determinations, and temperature control for physical measurements.

Starting at: Call For Price

Thermoelectric Cold Plate

3" diameter top plate. Cabinet dimensions 7 1/4" x 5 1/2" x 4 3/4". Power requirements 50 watts. This unit uses the most efficient solid state thermoelectric modules yet developed. DC power is supplied to these high powered modules to control temperatures between +25^o C and -20^o C depending on the set point required. All units may use air cooling with built-in fan, or tap water cooling as the heat exchanger. Equilibrium is reached in 2-3 minutes. Lightweight, portable. Has been used successfully in recrystallizations, freezing point determinations, and temperature control for physical measurements.

Starting at: $675.00

Hot Plates

A general duty hot plate for use in every laboratory. Has a demand type thermostatic control which holds the temperature of the flat cast aluminum top to within +/- 5^o F. Temperature range is 200^o to 700^o F. Automatic stepless control. The sturdy SS case is attractive and easy to clean. Ample ventilation keeps controls and bench tops cool, and prolongs life of the unit. Supplied with pilot light and 6' 3" cord with three-way plug. UL and CSA approved. Operates on either 110-120 VAC or 240 VAC, 50/60 Hz. Dimensions: Top plate, 6 1/4L x 6 1/4 in.W, Overall, 7 5/8L x 65 /8W x 4 1/2 in.H.

Starting at: $469.95

32136 - Combination Hot Plate / Stirrer

Separate stirring and heating switches. Stirring and heating may be used simultaneously or independently. Stirring speeds adjustable between 60-1650 rpm. Recommended for stirring squeous liquids with viscosities less than or equal to 100% glycerol. One liter flask capacity. Extended safety front separates controls from hot surfaces. Thermostat controlled temperature adjustable up to 382o C. 6" x 6" solid aluminum top plate assures fast, steady heating. Includes 1/2" and 1 1/2" stir bars. Overall dimensions: 7 1/2" deep x 6" wide x 4 3/4" high. 120 VAC, 60 Hz, 500 watts.

$715.00

11493 - Low Profile PanaVise Head

Same mechanical features as Standard PanaVise Head, except that stem is attached to rear of head to permit positioning work closer to the work bench. Heavy-duty steel jaws may be interchanged with optional accessory nylon jaws. By combining with optional Low-Profile Base, the work piece can be swung out and away from the work bench for clearance.

$55.95

11492 - Standard PanaVise Base

Base design allows tilting, turning and rotating of head to any position. Load control knob and split-ball features permit locking, changing position or easy head removal. Three base mounting holes allow for permanent mounting on benchtop or portability when attached to Tray Base Mount, (sku: 11494). Base diameter 5", overall height 3 13/16".

$41.95

11650 - Glass Water Still

This traditional distillation unit produces from 300 - 400 ml per hour from a 1000 ml flask. This water has been shown to have a conductivity of 7 x 10^-7 Mhos, and to be essentially free from biological contamination. Hardware, heating mantle and powerstat included.

Call For Price

L59002 - Optional BiPod Polisher Accessory - Wedge Polisher Mount

Designed specifically for wedge polishing of TEM specimens. the mount consists of a small aluminum clamping mechanism and 5 Pyrex rods which slide into the center of the clamp and are held in place when the L-bracket is tightened. Not included with the purchase of the BiPod Polisher.

$195.00

Ultra Violet Curing Chamber

Designed for quick, easy polymerization of both plastic embedding media and plastic mounting media. Specimen tray designed to hold up to 12, 3" x 1" glass slides. Ultraviolet peak radiation is 320-360 nm, so presents minimal hazard to user. Can be operated at temperatures as low as 0o C for heat sensitive specimens. Unit is compact and lightweight with external dimensions of 5 1/4" high x 5 1/2" deep x 19" wide. Has hinged top for easy access to specimen tray. Operates on 110-120 VAC, 60 Hz at less than 1 amp. Step-down transformer available for 220-240 VAC, 50-60 Hz. Replacement lamps available . Capsule holder included.

Starting at: Call For Price

L03145 - BiPod Polisher Accessory - Foot for BiPod Polisher

Priced at $21.00 individually. Included at no charge with the purchase of the BiPod Polisher.

$21.00

My Account

Water Purification & Detection, Light Tables, Lab Balances & More

30274 - Center It - A Tube Drilling Jig

30275 - Bench Top Drill Press

11695 - Step-Down Transformer

11690 - Powerstat

11685 - Still Support Hardware

11680 - Heating Mantle

11675 - Glass Receiving Flask

11670 - Glass Column Condenser

11665 - Kjeldahl Connecting Bulb

11660 - Glass Stopper

11655 - Glass Boiling Flask with Side Arm

11285 - Double Clamp Holder

11490 - PanaVise Vacuum Base

11491 - Standard PanaVise Head

L03094 - Tripod Polisher Accessory - Plain L Bracket

Tripod Polisher Accessory - Slotted L Bracket - L03090 - L03090

L590TS - Tripod Polisher for TEM and SEM

EBSD (Electron Backscatter Diffraction) Polishing and Storage Kit

Digital Stir Kool, Combination Cold Plate and Stirrer w/GLASS THERMAL PROBE 5"

Stir Kool, Combination Cold Plate and Magnetic Stirrer

Digital Thermoelectric Cold Plate

Thermoelectric Cold Plate

Hot Plates

32136 - Combination Hot Plate / Stirrer

11493 - Low Profile PanaVise Head

11492 - Standard PanaVise Base

11650 - Glass Water Still

L59002 - Optional BiPod Polisher Accessory - Wedge Polisher Mount

Ultra Violet Curing Chamber

L03145 - BiPod Polisher Accessory - Foot for BiPod Polisher

Our Address

Newsletter

Our Company

Customer Service