Laboratory Supplies - Disposables, Storage, Safety Aids & More

This unit literally pumps thermal energy down the drain. As power is applied to the rugged thermo-electric modules, heat is transferred from the cold plate to the heat exchanger. The heat exchanger is maintained at tap water temperature by a hose connection to the 1/4 inch tubing at the rear of the instrument. A flow of one liter of tap water per minute through the heat exchanger is sufficient to carry excess heat down the drain. The unit has a low temperature limit approximately 40^oC below that of the tap water. The unit is recommended for solutions up to 200ml and uses a 3 inch diameter top plate from which heat is extracted at an initial rate of 130 BTU/hr. There is a built-in magnetic stirrer with speed control which, combined with a magnet bar in the solution, will keep your solution at equilibrium. The digital meter controller is very easy to set. Just follow the simple instructions to dial in the desired temperature for your project. The controller will maintain the set point to +/- 0.1^oC accuracy.

Accessories for the Stir Kool can be found HERE. 

Designed for quick, easy polymerization of both plastic embedding media and plastic mounting media. Specimen tray designed to hold up to 12, 3" x 1" glass slides. Ultraviolet peak radiation is 320-360 nm, so presents minimal hazard to user. Can be operated at temperatures as low as 0o C for heat sensitive specimens. Unit is compact and lightweight with external dimensions of 5 1/4" high x 5 1/2" deep x 19" wide. Has hinged top for easy access to specimen tray. Operates on 110-120 VAC, 60 Hz at less than 1 amp. Step-down transformer available for 220-240 VAC, 50-60 Hz. Replacement lamps available . Capsule holder included.

Set of 75 straight side glass vials with flat bottoms and black plastic screw caps. Each bottle has a volume of 2 drams, is 17 mm diameter x 60 mm high.

Designed specifically for wedge polishing of TEM specimens. the mount consists of a small aluminum clamping mechanism and 5 Pyrex rods which slide into the center of the clamp and are held in place when the L-bracket is tightened. Not included with the purchase of the BiPod Polisher.

Our new mini-centrifuge is the perfect answer for quick spin-downs from tubewalls and caps, HPLC preparations, cell separations and micro-filtration tubes. The tiny footprint and quiet operation makes it perfect for desktop use or quick transport between countertops. A great convenience and a superb value!

Specifications:

• rpm: 6,000
• Relative Centrifugal Force: 2,000g
• Capacity: 6 x 1.5ml
• Operating Temperature: Ambient
• Weight: 494g
• Dimensions: 120mm H x 130mm W x 137mm D
• Electrical: 110V;50/60Hz , 220V:50/60Hz

Small - The mini-centrifuge can easily squeeze onto a crowded countertop.

Safe - Turn centrifuge on and off without opening the lid using an independent switch.

Simple - A pop-open latch system and transparent lid allow you to monitor the sample while it spins. Polished ABS finish quickly wipes clean. Internal mini-transformer eliminates cumbersome adapters.

Quiet - The low-durometer foot grip and fiberglass-reinforced carbonate rotor assure sure-footed, noise-free operation.

Convenient - The 6 tube, fixed-angle rotor requires no unlocking, no releasing, just pop the tubes in and out. Included adapters quickly accommodate 0.5 ml tubes.

Slide Dispenser:

Made of stainless steel. Holds up to fifty-four 75 mm x 25 mm slides. Dispenses slides one at a time on down stroke of lever. Keeps slides essentially dust free. Convenient to use. 5" long x 3" wide x 4" deep.

P-80® Grip-it Quick-drying Temporary Assembly Lubricant eases installation of tight-fitting rubber and plastic parts by reducing the force needed for assembly. Once assembly is complete, P-80 Grip-it dries and provides resistance that helps keeps parts in place. P-80 Grip-it can be applied manually or automatically, by dip, brush, or spray techniques. P-80 Grip-it is ideal for insertion of hoses that are pressure-tested immediately after assembly, and in any application that requires a fast-drying lubricant. Typical uses include installation of hoses, grips, o-rings, seals, bushings, gaskets, grommets, and many other rubber and plastic parts.

Comes in packages of 24. Available in 4 ml, 8 ml, 12 ml, and 16 ml capacities.

The LBP310 laboratory microwave oven is a time and power level based microwave that incorporates the exclusive True-To-PowerTM power control system. This power control system allows the user to set the true power level to any value. Specifications - Output power: 800 watts - Required power: 110 volt, 60 Hz. (230 volt, 50Hz available) - Dedicated 15-amp line - Weight : 49 pounds Dimensions: - Outer: 20 1/2" w x 12 1/8" h x 16" d (W/O handle) - Cavity: 13 7/8" w x 8 1/8" h x 14 5/8" d Cavity exhaust airflow 15 cfm, into free air Operating frequency: 2.45 GHz (an internationally regulated ISM frequency)

120 Watts: - Exterior Dimensions: 13" w X 15" h X 11" d - Interior Dimensions: 12" w X 10" h X 10" d - Electrical: 115VAC*, 120 Watts - Operating Range: Ambient +2°C to 62°C 235 Watts: - Exterior Dimensions: 19" w X 21" h X 13" d - Interior Dimensions: 18" w X 16" h X 12" d - Electrical: 115VAC*, 235 Watts - Operating Range: Ambient +2°C to 62°C *All incubators are available in 230VAC at no additional charge. Please let us know at the time of your order.